作者机构：
[程园园; 刘大川] Department of Food Science and Engineering, Wuhan Polytechnic University, Wuhan, 430023, China;[刘晔] Department of Environmental and Chemical Engineering, Wuhan Polytechnic University, Wuhan, 430023, China;[张麟] Department of Mechanical Engineering, Wuhan Polytechnic University, Wuhan, 430023, China
通讯机构：
Department of Environmental and Chemical Engineering, Wuhan Polytechnic University, Wuhan, China
摘要：
Cashew classification technology is tested by the method of orthogonal test in this paper, and it found the main factors, the trend and the optimum operating parameters of cashew classification by observing three factors of the sieve length, drum speed and the number of turns which influenced mixed-level rate and classification efficiency. We did regression analysis of test data by using SPSS software, and got the universal formula of cashews samples grading for cashews samples. The paper provided theoretical basis for the structural design and optimization of the operating parameters of the cashew grading machine.
关键词：
Experimental research;Kernel and husk separation;Rapeseed;Vibrating fluidized classification
摘要：
For improving the stability of kernel and husk separation machine of rapeseed, we had done some experimental research about vibrating fluidized classification technology. Based on experimental dates we had built the mathematics model and analyzed the classification effect influenced by the amplitude, the frequency and the material thickness and their interaction .The results indicated that when we maintained installation angle α = 0o and vibration direction angle β =108o of the vibrated fluidized bed, the best optimized combination of factors was the amplitude x1 = 1.87mm, the frequency x2 = 52.53Hz and material thickness x3 = 22.36mm.
期刊：
Applied Mechanics and Materials,2010年29-32:1753-1757 ISSN：1660-9336
通讯作者：
Xu Hongwen
作者机构：
[Xu Hongwen] China Univ Geosci, Fac Mech & Elect Informat, Wuhan 430074, Peoples R China.;[Zhang Qizhi] Wuhan Polytech Univ, Wuhan, Peoples R China.;[Zhang Lin] Wuhan Polytech Univ, Sch Mech Engn, Wuhan, Peoples R China.
通讯机构：
[Xu Hongwen] C;China Univ Geosci, Fac Mech & Elect Informat, Wuhan 430074, Peoples R China.
会议名称：
2010 International Conference on Applied Mechanics and Mechanical Engineering, ICAMME 2010
会议时间：
8 September 2010 through 9 September 2010
会议地点：
Changsha, PEOPLES R CHINA
会议主办单位：
[Xu Hongwen] China Univ Geosci, Fac Mech & Elect Informat, Wuhan 430074, Peoples R China.^[Zhang Qizhi] Wuhan Polytech Univ, Wuhan, Peoples R China.^[Zhang Lin] Wuhan Polytech Univ, Sch Mech Engn, Wuhan, Peoples R China.
会议论文集名称：
Applied Mechanics and Materials
关键词：
Coat;Detonation spraying;Wear resistance
摘要：
To improve the using life of screw, the paper focused on the research about microhardness and wear resistance of surface detonation spraying coat. The detonation spraying surface was important to extend the wear resistance of screw of low temperature screw press machine. The paper analyzed the phase composition and microstructure data of surface detonation spraying coat and tested the microhardness of coat and combination intensity between coat and substrate, and did contrasting wear resistance experiment between detonation spraying coat and traditional coat. The data analysis results showed that the wear resistance of detonation spraying coat was far beyond traditional coat and the detonation spraying coat would improve the using life of key screw of low temperature screw press machine.
期刊：
2010 International Conference on Mechanic Automation and Control Engineering,2010年:3254-3256
通讯作者：
Zhang, L.
作者机构：
[Zhang Lin] School of Mechanical Engineering, Wuhan Polytechnic University, Wuhan, China;[Zhang Qizhi] Library, Wuhan Polytechnic University, Wuhan, China;[Xu Hongwen] Faculty of Mechanical & Electronic, China University of Geoscience, Wuhan, China
通讯机构：
School of Mechanical Engineering, Wuhan Polytechnic University, China
会议名称：
2010 International Conference on Mechanic Automation and Control Engineering
会议时间：
June 2010
会议地点：
Wuhan
会议论文集名称：
2010 International Conference on Mechanic Automation and Control Engineering
摘要：
Digital composite structures definition is the basis for the data integration of CAD, CAE and CAM for composite structures. The key of digital composite structures definition is the modeling of material structures. In this paper the procedure of material structures modeling and contents of laminate lay-up definition data have been summarized briefly. Today composite structures can not be analyzed with true fiber orientations. True fiber orientations of discrete triangle elements have been used to approximate the final state of ply fibers and a XML file has been used to describe laminate lay-up definition data. Furthermore, automatic mapping of fiber orientation data to the finite element mesh based on user specified tolerances has been used to obtain the automatic data transfer from CAD software to CAE software. Finally, the data integration of the CAD software with two manufacturing systems has been presented.
期刊：
OPEE 2010 - 2010 International Conference on Optics, Photonics and Energy Engineering,2010年2:228-231 ISSN：2158-7434
通讯作者：
Xu, H.(xuhwxuhw@163.com)
作者机构：
[Hongwen Xu] Faculty of Mechanical and Electronic Information, China University of Geosciences, Wuhan 430074, China;[Qizhi Zhang] Library Wuhan Polytechnic University, Wuhan 430074, China;[Xinchuan Li] College of Computer Science, China University of Geosciences, Wuhan 430074, China;[Lin Zhang] School of Mechanical Engineering, Wuhan Polytechnic University, Wuhan 430074, China
会议名称：
2010 International Conference on Optics, Photonics and Energy Engineering (OPEE)
会议时间：
May 2010
会议地点：
Wuhan
会议论文集名称：
2010 International Conference on Optics, Photonics and Energy Engineering (OPEE)
作者机构：
[张麟; 刘大川] Department of Machinery Engineering, Wuhan Polytechnic University, Wuhan 430023, China;[刘金波; 叶平; 张安清] Anlu Tianxing Grain and Oil Machinery Manufacturing Company, Anlu 432600, China
通讯机构：
Department of Machinery Engineering, Wuhan Polytechnic University, China
